Introduction
Connecting a WhatsMiner ASIC to a mining pool is normally a short procedure: locate the miner's IP address, sign in to its local web interface, enter the pool's connection details, save the configuration, and confirm that the miner begins submitting shares. The individual fields rarely change, but their exact labels, menu locations, and default login behavior can vary between WhatsMiner models and firmware versions. This guide walks through the general workflow and uses ViaBTC's standard BTC mining endpoint as a concrete, clearly labeled example. Readers mining a different coin, using ViaBTC Smart Mining, or connecting to another pool should substitute that pool's own current connection details rather than reusing the values shown here.
What You Need Before Configuring a WhatsMiner
Before starting, confirm that the following are in place:
- A powered WhatsMiner unit connected to the network by Ethernet
- A computer or mobile device on the same local network as the miner
- The miner's administrator login credentials for its web interface
- An account with the target mining pool, along with the user ID or mining identifier the pool requires
- The pool's current Stratum URL, port, worker-name format, and password requirement, taken from that pool's official documentation
Because pool endpoints and ports can change, copy these values from the pool's current documentation at the time of setup rather than from an older tutorial, screenshot, or forum post.
Step 1: Find the WhatsMiner's IP Address
The miner's local IP address is required to reach its web interface. Two common methods are available.
The first is to check the connected-device list on the network router or DHCP server; WhatsMiner units typically appear with a hostname that includes the model or serial number.
The second is WhatsMinerTool's IP Monitor function, which is useful when multiple miners are deployed and manual router lookup is impractical. In WhatsMinerTool, select IP Monitor, click Start, then press and hold the IP Found button on the physical miner until its indicator lights flash; the corresponding IP address then appears in the tool. WhatsMiner's support documentation describes this workflow in detail.
Step 2: Log In to the WhatsMiner Web Interface
Enter the miner's local IP address into a web browser on a device connected to the same network. This opens the miner's built-in configuration interface, which requires a username and password specific to that model and firmware version.
Login credentials differ across WhatsMiner generations and firmware releases, and MicroBT has adjusted default-credential practices over time for security reasons. Rather than assuming a default username and password, check the credentials printed on the miner's label, the documentation that shipped with the unit, or MicroBT's current official support materials for that specific model.
Step 3: Open the Pool Configuration Page
Once logged in, locate the pool configuration section of the interface. On many WhatsMiner firmware versions this is found under Configuration → CGMiner Configuration, reflecting the miner's use of CGMiner-based mining software to manage Stratum connections. The exact menu wording can differ by firmware build and miner generation, so treat this as a general reference point rather than a fixed path that applies to every unit.
This page typically presents three pool slots (Pool 1, Pool 2, Pool 3), each with fields for URL, worker, and password.
Step 4: Enter the Pool URL, Worker Name, and Password
Each pool slot requires three pieces of information:
Stratum URL. This identifies the pool server and port the miner connects to in order to receive work and submit shares. It is a network address, not a Bitcoin wallet address, and entering a wallet address in this field will not allow the miner to connect correctly.
Worker name. This identifies which account, and which specific miner within that account, submitted a given share. ViaBTC's BTC mining documentation specifies a userID.workerID format, with the worker-ID portion limited to lowercase letters and numbers and a maximum length of 64 characters. Assigning a distinct worker ID to each machine — for example, farm01, farm02, farm03 — makes individual miners easier to identify on the pool's dashboard, though this is an operational convenience rather than a protocol requirement.
Mining password. Some pools require a password for the Stratum connection; ViaBTC's BTC mining setup accepts a placeholder value such as x because a password is not required for this configuration. This field is separate from the pool account's login password, and the account password should not be entered here.
For ViaBTC's standard BTC mining pool, a working configuration looks like this:
Pool 1 URL: stratum+tcp://btc.viabtc.io:3333
Worker: yourUserID.worker01
Password: x
These values apply specifically to ViaBTC's standard BTC mining endpoint. ViaBTC Smart Mining uses a different hostname, and other coins or pools will have their own URL and worker conventions, so these should be confirmed against ViaBTC's BTC Mining guide and current Mining Pools Information page before use.
Step 5: Add a Backup Connection
Most WhatsMiner firmware allows multiple pool entries so the miner can attempt the next configured connection if the primary one becomes unreachable. For ViaBTC's BTC mining endpoint, port 443 on the same hostname serves as a documented failover option:
Pool 2 URL: stratum+tcp://btc.viabtc.io:443
Worker: yourUserID.worker01
Password: x
This second entry is a backup connection to the same pool, not a separate mining pool or a separate account. A third slot can be left blank or configured with another backup address if the pool documentation provides one.
Step 6: Save, Allow the Miner to Reconnect, and Check Status
After entering the pool details, save the configuration. The miner will typically reconnect within a short period and begin submitting shares to the configured pool.
Check the miner's own status page first to confirm that it reports an active connection and a non-zero hashrate reading. Then check the corresponding Workers page on the pool's dashboard — for ViaBTC, this is the Workers section of the BTC mining account. Allow roughly 10–15 minutes after the miner stabilizes before expecting the worker to appear as active on the pool side, since the pool's dashboard updates on its own schedule rather than instantaneously with the miner's local display.
Troubleshooting Common WhatsMiner Pool Setup Problems
Several issues account for most connection failures:
- Wrong coin or mining-mode endpoint. Using the standard BTC endpoint will not apply your One-click Switch settings. When using the Smart Mining endpoint, check the coin selected in your account’s Smart Mining settings to ensure the miner is mining the intended coin.
- Typographical errors. A misspelled hostname, incorrect port, or malformed worker name is a common cause of failed or rejected connections.
- Wallet address used as worker name. The worker field expects the pool's worker-naming format, not a BTC payout address.
- Credential confusion. The miner's web-interface login, the pool account login, and the Stratum password field are three separate credentials; mixing them up can block access to the miner or cause the pool connection to fail.
- Network or DNS restrictions. Firewalls, VPNs, or DNS filtering on the local network can prevent the miner from reaching the pool's Stratum server even when the configuration itself is correct.
- Persistent rejected shares. Occasional rejected shares are normal, but a consistently high rejection rate usually points to a configuration or network issue rather than a hardware fault, and is a more informative indicator of connection health than a single hashrate reading.
For security reasons, always copy pool URLs from the pool's own official documentation. ViaBTC has previously issued a notice warning users against unofficial pool URLs and unofficial mining-agent software; the same caution applies generally when sourcing connection details from third-party sites or outdated guides.
Batch Configuration with WhatsMinerTool
Operators managing multiple WhatsMiner units can configure pool settings in batches through WhatsMinerTool rather than logging into each miner's web interface individually. The tool's pool-configuration function allows fixed pool inputs and worker-suffix handling to be applied across a group of miners at once. Some of these batch-configuration features require firmware later than version 20241011.12, so operators using older firmware may need to update before these functions become available, as described in WhatsMiner's Operation Guide.
Understanding Shares and Hashrate Readings
A pool assigns miners a share target that is numerically higher — and therefore easier to meet — than the Bitcoin network's block target, which corresponds to lower difficulty for an individual share. Submitted shares that meet this easier target let the pool estimate each miner's contribution and apply its reward-accounting method, as described in the Bitcoin Developer Guide's mining documentation. Accepted and rejected share counts are therefore a more direct indicator of connection health than a single instantaneous hashrate reading.
It is also worth distinguishing between the hashrate shown on the miner itself and the hashrate the pool reports. The miner's local display reflects its own measurement, while the pool estimates hashrate from shares received over its own measurement window. Short-term differences between these two figures are expected, since they are separate measurements taken over potentially different time windows; neither figure should be treated as simply more accurate without specifying the measurement period being compared.
FAQ
Which URL should I use?
Use the URL published in the pool's current official documentation for the specific coin and mining mode you intend to use. For ViaBTC's standard BTC mining, this is btc.viabtc.io on the documented port; ViaBTC Smart Mining and other pools use different hostnames, so confirm the correct endpoint before configuring the miner.
Do I need a mining password?
It depends on the pool. ViaBTC's BTC mining setup does not require a meaningful password and accepts a placeholder such as x. This Stratum password field is unrelated to the pool account's login password, which should never be entered into the miner's configuration.
Why is the pool hashrate different from the miner display?
The miner reports its own local measurement, while the pool calculates an estimate from shares received over its own measurement window. These are two different measurements taken over potentially different time periods, so short-term differences are normal rather than indicative of a fault.
Why is the worker inactive?
A worker may show as inactive immediately after configuration simply because the pool dashboard has not yet updated; allow roughly 10–15 minutes after the miner stabilizes before investigating further. If the worker remains inactive beyond that, check for a typographical error in the URL, port, or worker name, and confirm that the miner is actually submitting shares rather than idling due to a network restriction.
Should each miner use a different worker ID?
Assigning a unique worker ID to each machine is not a requirement of the Stratum protocol, but it makes individual miners easier to identify and monitor on the pool's dashboard, which is useful in multi-miner deployments.
References
- ViaBTC Help Center, "BTC Mining," https://support.viabtc.com/hc/en-us/articles/7207401012879-BTC-Mining
- ViaBTC Help Center, "Mining Pools Information," https://support.viabtc.com/hc/en-us/articles/14367481714191-Mining-Pools-Information
- WhatsMiner Support, "How does WhatsMinerTool assist in configuring miner IP addresses," https://support.whatsminer.com/en-US/article/411
- WhatsMiner Support, "WhatsMinerTool Operation Guide," https://support.whatsminer.com/en-US/article/487
- Bitcoin Developer Guide, "Mining," https://developer.bitcoin.org/devguide/mining.html


