Bitcoin Cash (BCH) uses the same SHA-256 proof-of-work algorithm as Bitcoin, which means SHA-256 ASIC hardware already deployed for Bitcoin mining can also be pointed at a BCH mining pool. For a new miner, the practical questions are rarely about cryptography — they are about how a pool measures contributed work, how rewards are calculated, and what to check once a miner is connected. This article walks through that process using ViaBTC's BCH pool as a concrete reference point.
What Is a Bitcoin Cash Mining Pool?
Finding a BCH block alone (solo mining) requires producing a valid proof of work that meets the network's current block target, a statistically rare event for any single ASIC given current network conditions. A mining pool aggregates the hashing work of many participants and calculates each miner's earnings according to their contributed work and the selected payout method. Whether those earnings depend on the pool finding a block varies by payout method.
To measure each participant's contribution, the pool assigns miners a share target that is easier to satisfy than the BCH network's block target. Each valid proof of work a miner submits that meets this share target is called a share. A share that also happens to satisfy the stricter network target produces a valid block. This mechanism — a pool issuing a share target and distributing work over a protocol such as Stratum — is part of how mining pools coordinate work across many devices (Bitcoin developer guide: mining and Stratum).
What You Need Before Mining BCH
Three things are required before a BCH mining session can begin.
A SHA-256-compatible ASIC is the hardware requirement; general-purpose CPUs and GPUs are not competitive for BCH mining under current network difficulty. A stable power supply and internet connection are also necessary, since intermittent connectivity causes a miner to repeatedly reconnect and resubmit work, which can reduce the share rate the pool records for that worker. Finally, a pool account is needed, along with a configured payout address or balance settings for receiving BCH.
BCH targets an average block interval of 10 minutes, with difficulty adjusting over time to keep production close to that average rather than fixing the interval of any single block (Bitcoin Cash proof of work). The block subsidy halves every 210,000 blocks and currently stands at 3.125 BCH per block at 2026 block heights; the total coinbase reward a pool receives for a found block can exceed this figure because transaction fees are added on top of the subsidy.
How BCH Mining Pools Measure Your Contribution
Three distinct figures appear once a miner is connected, and beginners frequently confuse them.
ASIC-reported hashrate is a reading calculated by the mining device itself from its own internal work counter. Pool-estimated hashrate is a separate estimate the pool calculates from the valid shares a worker has submitted over a defined window — for example, a real-time figure based on the preceding several minutes, and a daily average based on the preceding 24 hours. Network hashrate is an estimate of total BCH hashing power across all miners and pools, generally inferred from recent blocks and the current difficulty.
These three numbers are not interchangeable, and a mismatch between them does not necessarily indicate a hardware fault. A miner that has just started, or that experienced a brief disconnection, may show a higher short-term hashrate on its own display while the pool's 24-hour average remains lower, simply because the pool's longer averaging window still includes the earlier period of reduced or absent output.
Rejected shares are the broader category that covers several possible subtypes, including stale, invalid, and duplicate shares. A rejection rate that rises noticeably and persists is a reasonable prompt to check the configured pool address, the miner's system clock, network latency to the pool, firmware version, and general hardware condition — though no single rejection-rate threshold is a universal pass/fail standard, and readers should treat occasional rejected shares as a normal part of pool mining rather than evidence of malfunction.
PPS+ vs. PPLNS for BCH Mining
ViaBTC currently offers two payout methods for BCH: PPS+ and PPLNS. The distinction lies in how the block-reward and transaction-fee components of mining income are handled.
Under PPS+, the block-reward portion of income is calculated and credited using Pay-Per-Share (PPS) logic based on the miner's submitted work and current difficulty, while the transaction-fee portion is distributed using Pay-Per-Last-N-Shares (PPLNS) logic. Under PPLNS, both the block reward and transaction fees follow PPLNS rules, meaning a miner's payout depends on its share of the pool's total work over a trailing window of difficulty rounds, settled after a pool-found block reaches six confirmations (ViaBTC payout-method explanation).
This is a mechanical difference in how reward variance and timing are allocated across the block-reward and fee components — it does not make either method a guaranteed daily BCH amount. Earnings under both methods still move with valid share submission, network difficulty, pool uptime, and the fee schedule applied to each component.
How to Connect a Miner to ViaBTC's BCH Pool
Once an ASIC is physically installed and reachable on the network, the configuration steps are similar across most SHA-256 miner brands:
- Open the miner's pool configuration page and enter a currently documented ViaBTC BCH endpoint, such as
stratum+tcp://bch.viabtc.io:3333. Because pool addresses can change over time, it is advisable to confirm the current endpoint list rather than reuse an address from an older guide (ViaBTC BCH mining setup). - Enter the worker name using the format
userID.workerID, where the worker ID may use lowercase letters and numbers up to 64 characters; a password is optional for this field. - Configure a second and, where supported, a third pool endpoint as backups, so the miner can fail over automatically if the primary connection becomes unreachable.
- Save the configuration and allow the miner to run uninterrupted. According to ViaBTC's documentation, a newly connected worker typically becomes visible on the dashboard after roughly 10–15 minutes of stable operation.
What to Monitor After Your Miner Connects
After the initial connection period, four areas of the dashboard are worth routine attention.
Worker status indicates whether a given device is actively submitting shares or has gone inactive, which is usually the fastest way to notice a disconnected or powered-down unit. Pool-estimated hashrate, both the short-window and daily-average figures, shows the pool's measurement of contributed work; a lower daily figure shortly after startup is expected and not inherently a problem. Rejected shares should be checked periodically rather than reacted to for every isolated occurrence, with attention paid to the trend rather than any single reading.
Earnings and payout settings cover a separate stage of the process: reward calculation under the selected payout method, account balance crediting, and withdrawal processing are distinct steps, not a single combined "daily payout." ViaBTC's current documentation lists a BCH automatic-withdrawal minimum of 0.001 BCH, with automatic withdrawals processed once daily during a defined window, separate from the hourly or round-based crediting of mining rewards to the account balance. Readers should confirm the current minimum and processing schedule directly in their account settings, since platform parameters can be updated.
How to Evaluate BCH Mining Earnings
A pool dashboard or a profitability calculator can show an estimated BCH-per-TH/s figure, but this is a dynamic estimate, not a forecast or a guarantee. Several inputs move independently and should be considered separately rather than collapsed into a single number:
- Network difficulty rises and falls with total network hashing power; higher difficulty reduces the expected reward per unit of hashrate, all else equal.
- BCH market price affects the fiat value of any BCH earned, independent of the mining process itself.
- Pool fees differ by payout method — for example, PPS+ currently applies separate fee treatment to its block-reward and transaction-fee components, while PPLNS applies a single fee rate to the combined reward. Readers should confirm current fee percentages on the pool's published fee schedule before estimating net earnings.
- Electricity cost is a direct operating expense measured in cost per kWh consumed, distinct from pool fees.
- Uptime and rejected shares affect how much valid work is actually credited over a given period; downtime and rejected work are not the same effect and should not be subtracted from earnings estimates twice.
Because network hashrate, difficulty, and pool hashrate shift continuously, any such figures cited in an article or calculator should be treated as a dated snapshot rather than a stable benchmark, and verified against current pool statistics immediately before relying on them.
Frequently Asked Questions
Can I mine BCH with a Bitcoin ASIC?
Yes. Bitcoin Cash uses SHA-256, the same algorithm as Bitcoin, so SHA-256 ASICs built for Bitcoin mining are also compatible with BCH mining pools; the miner simply needs to be pointed at a BCH-specific pool endpoint rather than a BTC endpoint.
What is the difference between BCH solo mining and pool mining?
In solo mining, a single miner must independently find a full block matching the network's block target, which is statistically rare for most individual ASICs at current difficulty. Pool mining combines many miners' work and calculates each miner's earnings according to their contribution and the selected payout method. Under ViaBTC's PPS+, the base PPS earnings do not depend on the pool finding a block, while PPLNS earnings depend on blocks found by the pool.
What is a mining share?
A share is a proof of work submitted by a miner that satisfies the pool's assigned share target, which is set easier to meet than the BCH network's block target. Shares let the pool measure each miner's contributed work; occasionally a share also satisfies the network target and becomes a valid block.
Why does my ASIC hashrate differ from the pool's hashrate?
ASIC-reported hashrate is calculated locally by the device, while pool-estimated hashrate is derived from valid shares submitted over a specific averaging window, such as the preceding 24 hours. A mismatch — particularly a lower pool average shortly after startup or after downtime — is often explained by the averaging window rather than a hardware problem.
What is the difference between PPS+ and PPLNS?
Under PPS+, the block-reward component of income is calculated using PPS logic while transaction fees are distributed using PPLNS logic. Under PPLNS, both the block reward and transaction fees follow PPLNS logic. The two methods differ in how reward variance and timing are allocated, not in whether earnings are guaranteed.
How long does it take for a new worker to appear?
ViaBTC's BCH setup documentation indicates a newly connected worker typically becomes visible on the pool dashboard after approximately 10–15 minutes of stable, uninterrupted operation.
Why are my shares being rejected?
Rejected shares can result from several causes, including stale shares, invalid shares, or duplicate submissions. A sustained increase is a reasonable reason to check the configured pool address, the miner's system clock, network latency, firmware settings, and overall hardware condition.
Is a mining-profit calculator a guarantee of future income?
No. A profitability estimate reflects current conditions such as difficulty, BCH price, and fee assumptions at a single point in time. Actual results can differ as difficulty, price, pool fees, electricity costs, and uptime change.


